A Pattern Recognition Method of Personalized Adaptive Learning in Online Education

Mobile Networks and Applications - In order to effectively identify the pattern of personalized adaptive learning in online education and improve the recommendation satisfaction of personalized...     

Improving gelling properties of myofibrillar proteins incorporating with cellulose micro/nanofibres

The effects of cellulose microfibres (CMFs, Average size: 100 ± 5 μm) and cellulose nanofibres (CNFs, Average size: 60 ± 3 nm) on the properties of myofibrillar protein (MP) gels from duck breast meat were studied. The results demonstrated that CMFs and CNFs were mostly connected to MP by non-covalent bonds, the diffusion and cross-linking of MP molecules was promoted, and a denser and more complete gel network was formed. With the increases of CMFs and CNFs concentration (0–10%), the hardness was increased by 13.15% and 19.78% for CMFs10% and CNFs10% gels, respectively, and the elasticity was increased by 40% and 80%, respectively. At the same concentration (0–10%), the increase in gel hardness, viscoelasticity and immobilised water content was greater in the CNFs-MP group than in the CMFs-MP group. The CNFs-MP group had a tighter gel network, and CNFs had a better potential to improve the gelation performance of MP.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Enhanced thermal conductivity of PP hybrid films induced by filler orientation and laminated structure

Journal of Materials Science - Currently, polymeric composites with good thermal conductivity and simple preparation method are in the rapid increment of demand. In this work,...     

Oxidative characteristics and gel properties of porcine myofibrillar proteins affected by l-lysine and l-histidine in a dose-dependent manner at a low and high salt concentration

This study investigated the effects of l -lysine (Lys) and l -histidine (His) on the oxidative characteristics and gel properties of porcine myofibrillar proteins (MP). Results showed that Lys and His had a strong ferrous ion-chelating ability and hydroxyl radical-scavenging activity. Moreover, Lys and His inhibited the protein carbonyl formation and MP aggregation at 0.2 M and 0.6 M NaCl, respectively, in a dose-dependent manner. Furthermore, 2 and 4 mg mL⁻¹ Lys and His decreased the oxidation-induced loss of the tertiary structure of MP accompanied by the lower surface hydrophobicity. The water-holding capacity and gel strength of MP gels increased with increasing Lys and His concentrations due to more regular and lamellar structures with smaller and homogeneous pores at 0.6 M NaCl and more orderly crosslinking via fibrous filament at 0.2 M NaCl. In summary, Lys and His chelated the ferrous ions and scavenged hydroxyl radicals, decreased the oxidation-induced physicochemical changes, thus preventing oxidative damage during the formation of a three-dimensional gel network, which resulted in better gel quality.     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.